R60 2012 R60 N18 oil filter housing.
#1
2012 R60 N18 oil filter housing.
Purchased the car used, 76,000 with the oil leak.
And now am tackling the leak. As I am reassembling the engine I noticed a small crack on the original housing. So ordered a replacement. Which brings me to my problem. The new housing is not fitted with a pressure switch.
is this normal? Should I just order another new one from a different vendor? Or should i just install it? If i do would that leave me in Limp Mide? Which then brings me to, how am I to know the pressure without the switch? Is there a MOD...
And now am tackling the leak. As I am reassembling the engine I noticed a small crack on the original housing. So ordered a replacement. Which brings me to my problem. The new housing is not fitted with a pressure switch.
is this normal? Should I just order another new one from a different vendor? Or should i just install it? If i do would that leave me in Limp Mide? Which then brings me to, how am I to know the pressure without the switch? Is there a MOD...
#2
#3
Update
Did the install, obviously being there's no pressure switch, I don't get a oil pressure LED or code.
Originally i had received P0524 Low Oil Pressure, and since it had a oil leak that was obvious. And also P0014 VVT retarded (A). Replacing the Oil Filter Housing repaired the oil leak and I no longer have (A) retarded Mini.
But now I get I get P0597 "Thermostat Heater Control Circuit/Open". Followed with, stalled cold start, rough idle, hesitation at acceleration almost like it's misfiring. No other MIL or DTC appear.
I had already replaced the plugs and coil packs. Maybe the Mini is retarded.....
Originally i had received P0524 Low Oil Pressure, and since it had a oil leak that was obvious. And also P0014 VVT retarded (A). Replacing the Oil Filter Housing repaired the oil leak and I no longer have (A) retarded Mini.
But now I get I get P0597 "Thermostat Heater Control Circuit/Open". Followed with, stalled cold start, rough idle, hesitation at acceleration almost like it's misfiring. No other MIL or DTC appear.
I had already replaced the plugs and coil packs. Maybe the Mini is retarded.....
#4
#5
Re
Yeah got the housing off Amazon, obviously the fitment guide has some flaws....
And replacing this one is definitely on the to do list. But being this is my daily driver and i was in a pinch to get the job done before work monday i have to make due.
But as for the stall and hesitations i was getting, turned out to be the HPFP... odd there is no DTC for it...
And being i now have the P0597 thermostat code, the plan is to tackle the correct housing at the same time I replace the thermostat housing... next weekend.
But for a quick repair, as far as it goes with the firing everything is smooth again, minus not having the pressure switch. But it does seem to lack the take off acceleration.
And replacing this one is definitely on the to do list. But being this is my daily driver and i was in a pinch to get the job done before work monday i have to make due.
But as for the stall and hesitations i was getting, turned out to be the HPFP... odd there is no DTC for it...
And being i now have the P0597 thermostat code, the plan is to tackle the correct housing at the same time I replace the thermostat housing... next weekend.
But for a quick repair, as far as it goes with the firing everything is smooth again, minus not having the pressure switch. But it does seem to lack the take off acceleration.
Last edited by Nix; 08-14-2022 at 04:16 PM.
#6
If you don’t mind me asking, where on the filter housing did you find the slight crack? I have a 2013 CM All4S (Dec 2012 build ) and I’m dealing with a leak. Thought it was the oil filter housing seals/cooler seals, but I could not find a smoking gun when I removed it from the car. Base on the pattern, it looked like the return oil turbo line had failed, but it was not the case. The feed line did not look like it was leaking and was not loose, however the dark grime was heavy in the area of the feed lined and return like at the block/housing end.
did you end up putting the bay in service mode to do the work? Any pictures/pointers you could share re: service mode?
I appreciate your response.
did you end up putting the bay in service mode to do the work? Any pictures/pointers you could share re: service mode?
I appreciate your response.
#7
Here are the correct parts:
N14 Engines:
https://www.ecstuning.com/b-genuine-...r/11428643749/
N18 engines.
https://www.ecstuning.com/b-genuine-...r/11428643745/
I have never seen one crack on the metal, its most of the time a the plastic cap cracks or there is a leak in the oil cooler or oil cooler to housing connection.
Oil filter housing DIY
https://www.northamericanmotoring.co...et-repair.html
N14 Engines:
https://www.ecstuning.com/b-genuine-...r/11428643749/
N18 engines.
https://www.ecstuning.com/b-genuine-...r/11428643745/
I have never seen one crack on the metal, its most of the time a the plastic cap cracks or there is a leak in the oil cooler or oil cooler to housing connection.
Oil filter housing DIY
https://www.northamericanmotoring.co...et-repair.html
__________________
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
Thread
Thread Starter
Forum
Replies
Last Post
Nick Perez
1st Gen Countryman (R60) Talk (2010-2015)
7
10-14-2017 10:19 AM
Drivetrain Broken O-ring around oil filter housing...
meb
Drivetrain (Cooper S)
21
03-19-2007 02:46 PM