Lost Black "MINI" circle on hood emblem
#1
Lost Black "MINI" circle on hood emblem
Hey guys. My MINI lost the black circle inside the hood emblem today. During a car wash. The chrome emblem is fine, just the black circle "MINI" is missing. Any way to replace that part without getting an entire new emblem?
Thanks!
its an R56 if that matters
Thanks!
its an R56 if that matters
#3
Been there before: https://www.northamericanmotoring.co...e-is-gone.html
Here is the rear emblem. It comes off with a heat gun or hair dryer and then you can use some dental floss to get under line. Use blue painter tape to make off the edges where the old one is, before you take it off , then plead and stick on the new one.
MINI Cooper Rear Trunk Emblem R50 R52 R53 , R56 R57
http://www.ecstuning.com/Search/SiteSearch/51147026186/
Otherwise if you like to replace the center and want to take the time to fit one in one of the center cap sticker off of the wheel and try to fit it to the wings emblem, the emblem is smaller then center caps sticker ~ 50mm (36136758687) and the wings MINI center ( 51147026186) sticker is about ~ 45mm in size. You could cut it to fit for something custom. Of course the MINI lgog should fit, but wont have the ring design. So it would take some craft and cutting.
MINI Logo Center Cap Sticker
http://www.ecstuning.com/Search/SiteSearch/36136758687/
Thanks
Here is the rear emblem. It comes off with a heat gun or hair dryer and then you can use some dental floss to get under line. Use blue painter tape to make off the edges where the old one is, before you take it off , then plead and stick on the new one.
MINI Cooper Rear Trunk Emblem R50 R52 R53 , R56 R57
http://www.ecstuning.com/Search/SiteSearch/51147026186/
Otherwise if you like to replace the center and want to take the time to fit one in one of the center cap sticker off of the wheel and try to fit it to the wings emblem, the emblem is smaller then center caps sticker ~ 50mm (36136758687) and the wings MINI center ( 51147026186) sticker is about ~ 45mm in size. You could cut it to fit for something custom. Of course the MINI lgog should fit, but wont have the ring design. So it would take some craft and cutting.
MINI Logo Center Cap Sticker
http://www.ecstuning.com/Search/SiteSearch/36136758687/
Thanks
__________________
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
#4
__________________
Your Trusted Source For DIY and Parts
FREE SHIPPING over $99 click here
MINI Parts | DIY Help | Facebook | Twitter | Instagram | YouTube | Promos
888.280.7799 | 6am - 5pm PST
FREE SHIPPING over $99 click here
MINI Parts | DIY Help | Facebook | Twitter | Instagram | YouTube | Promos
888.280.7799 | 6am - 5pm PST
#6
The discs are you best bet. But getting a new emblem helps , mine had the wings chipping when I changed it.
Plus you can put a pin on the back of your old one and pretend your a Pilot when you put it on your jacket.
Plus you can put a pin on the back of your old one and pretend your a Pilot when you put it on your jacket.
__________________
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
#7
Reviving this thread because the same thing happened to me, also after a blizzard. Mine is a 2005 R50, so I believe this is the correct part:
https://www.pelicanparts.com/More_In...rter=date_new#
Unfortunately I can't quite figure out how to replace it. As with the original poster, only the black enamel decal is missing, but I'm happy to replace the entire emblem to get a pristine look. Can someone point me to instructions on exactly how to do it? Folks have indicated that it "just sticks on," but there appear to be posts on the reverse, so I'm assuming I need to access the underside of the hood to get at the old one?
Thanks!
https://www.pelicanparts.com/More_In...rter=date_new#
Unfortunately I can't quite figure out how to replace it. As with the original poster, only the black enamel decal is missing, but I'm happy to replace the entire emblem to get a pristine look. Can someone point me to instructions on exactly how to do it? Folks have indicated that it "just sticks on," but there appear to be posts on the reverse, so I'm assuming I need to access the underside of the hood to get at the old one?
Thanks!
Last edited by ericwestby; 03-05-2018 at 06:09 AM. Reason: fixed a couple of errors
Trending Topics
#8
The following users liked this post:
ericwestby (03-08-2018)
#9
Reviving this thread because the same thing happened to me, also after a blizzard. Mine is a 2005 R50, so I believe this is the correct part:
https://www.pelicanparts.com/More_In...rter=date_new#
Unfortunately I can't quite figure out how to replace it. As with the original poster, only the black enamel decal is missing, but I'm happy to replace the entire emblem to get a pristine look. Can someone point me to instructions on exactly how to do it? Folks have indicated that it "just sticks on," but there appear to be posts on the reverse, so I'm assuming I need to access the underside of the hood to get at the old one?
Thanks!
https://www.pelicanparts.com/More_In...rter=date_new#
Unfortunately I can't quite figure out how to replace it. As with the original poster, only the black enamel decal is missing, but I'm happy to replace the entire emblem to get a pristine look. Can someone point me to instructions on exactly how to do it? Folks have indicated that it "just sticks on," but there appear to be posts on the reverse, so I'm assuming I need to access the underside of the hood to get at the old one?
Thanks!
https://www.northamericanmotoring.co...i-emblems.html
__________________
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
#10
#12
Thats great, much better!
__________________
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
Thread
Thread Starter
Forum
Replies
Last Post
Mini Mania
Drivetrain Products
2
05-09-2017 12:35 PM
Mini Mania
Interior/Exterior Products
0
01-19-2016 11:38 AM
Mini Mania
Interior/Exterior Products
0
01-15-2016 03:56 PM